Logistics / INSIGHTS

Container Seal Discrepancy: What to Check Before Handover

Published · 4 min read

A container seal discrepancy needs to be resolved before a shipment continues through a routine handover. A number that differs from the shipping documents may be a transcription error, an authorised replacement or a sign that the container was opened. The receiving team needs evidence to distinguish these possibilities.

This guide sets out a practical response for logistics teams receiving a sealed container. Apply the carrier's instructions and the site's safety and custody procedures throughout.

Start the container seal discrepancy check with identification

Check the container number first. A seal comparison is meaningless if the documents belong to another unit. Compare the physical container identification with the booking, transport instruction and available release or interchange record.

Read the entire seal number directly from the seal. Retain leading zeros and letters. Avoid relying on a driver's message, a spreadsheet entry or a photograph from a previous movement.

The CTU Code's receiving guidance calls for checking container identification, looking for signs of seal tampering, comparing the seal number with the documents and recording discrepancies. Notification and custody actions depend on the applicable procedures and national requirements.

Record the observation before discussing the cause

  • Container number and booking or job reference.
  • Seal number physically observed and the number on each relevant document.
  • Date, local time, time zone and exact inspection location.
  • Condition of the seal, locking assembly and accessible doors.
  • Names or roles of the receiving representative and carrier representative.
  • Clear photographs of the number, seal attachment and container identification, where safe and permitted.

Use factual wording: "Seal observed ABC00125; delivery record shows ABC00152." Avoid describing the shipment as tampered with unless evidence supports that conclusion.

Separate a data error from a physical exception

The seal is intact but its number differs

Ask the shipper and carrier to reconcile the original loading record, dispatch photographs and subsequent interchange records. Identify the first record where the number changed. A plausible typing error still needs a documented correction by the responsible party.

There is a documented replacement

Request the replacement record showing the container, previous seal, replacement seal, reason, location, date and responsible authority or operator. Check that the record belongs to this movement. A statement that "customs changed it" without a matching reference leaves the exception unresolved.

The seal is absent, damaged or appears disturbed

Escalate immediately through the carrier and shipper's nominated contacts. Keep the container under the applicable site controls. Do not cut a remaining seal, open the doors or fit a replacement merely to make the paperwork match. Agree the authorised next action and any required attendance before proceeding.

Keep one exception record and a clear owner

Open an exception against the shipment, then assign one coordinator to collect the evidence. Record who can approve release, who can correct transport data and who must receive the corrected information.

For example, a terminal observation, a carrier instruction and a shipper's packing record may arrive separately. Store them against the same container reference so that a later shift can understand the decision without rebuilding the conversation.

Keep the status precise: "seal discrepancy under review" is different from "released following documented seal replacement." A revised spreadsheet alone does not establish that the cargo was inspected or that custody was accepted.

Correct documents without erasing the audit trail

  1. Preserve the original discrepancy record and photographs.
  2. Obtain the responsible party's written explanation and supporting evidence.
  3. Confirm whether the shipping instructions, draft transport document, release instruction or other record needs correction.
  4. Route amendments through each document's authorised issuer; check the relevant submission deadline.
  5. Circulate the approved revision to the teams that actually use it.
  6. Record the release decision, decision-maker, time and any remaining conditions.

Do not silently overwrite an original seal number. Retain the relationship between the old entry, the verified observation and the approved correction.

Final handover checklist

  • The container identity is confirmed.
  • The physical seal and documentary record are reconciled, or the exception remains visibly open.
  • Required carrier, shipper and authority instructions have been followed.
  • The receiving team has the current revision.
  • Custody and onward-movement approval are recorded separately from document correction.

Key takeaways

Resolve the discrepancy through identification, evidence and an authorised decision. Keep the original record, distinguish a documentary correction from a physical inspection, and make the release status clear to the next team.

Contact ZSCM Logistics at logis@zscm.ae with your route, container reference and the discrepancy to be reviewed.

References

More insights

FREIGHT / REQUEST A QUOTE

Plan your
shipment.

Share your cargo, route and dates so we can review the freight options and service scope.

Request a freight quote
ZSCM
ZSCM LOGISTICSTRANSPORT / SUPPLY CHAIN
Trading division ↗Return to the opening ↗