Treat the return as a controlled transport leg. Confirm the carrier’s current instruction for the specific shipment and container before dispatching the truck.
Verify the Empty Container Return Location
Do not assume a depot used for a previous shipment remains valid. Instructions can change because of capacity or operating restrictions.
Check the carrier’s portal, delivery order or written notice using the bill of lading or shipment reference. Record:
- container number and size/type;
- bill of lading or shipment number;
- nominated return depot and full address;
- depot code where provided;
- instruction issue date and time;
- operating hours and appointment requirement;
- last date of free time;
- validation, pre-advice or release requirement;
- carrier contact for exceptions.
Maersk’s current support guidance, for example, directs customers to check the empty-return location against the shipment online. Its separate depot-change guidance requires a request through the carrier’s case-management process. These are carrier-specific procedures, so use the instructions that apply to the booked line and local office.
Confirm acceptance on the dispatch day
A depot named earlier may stop accepting a particular equipment type. Recheck the instruction before the vehicle leaves, especially after weekends, holidays, disruption notices or a long consignee delivery period.
Where the carrier publishes an empty-acceptance status, capture the result or reference. A screenshot can support the job file, but it does not override a later carrier instruction.
Check the Container Before It Leaves the Consignee
The consignee and driver should inspect the empty unit while access is still available. Record the condition without attempting unauthorised repairs.
Confirm:
- cargo and packing residue have been removed;
- container is reasonably clean and dry for return;
- doors close and locking bars operate;
- no cargo, dunnage or documents remain inside;
- exterior and interior damage is photographed;
- any reefer cable, genset or accessory responsibility is clear;
- container and seal records from the loaded movement are retained;
- driver has the correct container number on the transport order.
If the depot or carrier has cleaning, damage-survey or dangerous-residue requirements, obtain the applicable instruction. Do not describe a unit as undamaged merely because damage was noted at delivery; preserve the interchange and delivery evidence.
Reconcile Free Time and Validation
Identify how the carrier calculates import detention and when the empty must be accepted to stop the relevant clock. The contract, tariff and local rule control the calculation; a planned arrival at the depot may not be enough if the unit is rejected.
Before dispatch, check:
- discharge or availability date used for the calculation;
- agreed free-time days and calendar basis;
- final free date shown by the carrier;
- whether charges must be settled before return;
- whether credit customers need separate validation;
- evidence required if the nominated depot rejects the unit.
Carrier validation processes vary. A current Maersk customer advisory for a specific market, for example, distinguishes return steps by free-time and credit status and tells customers not to return until required validation is confirmed. Use such notices only for the market and period stated in them.
Escalate a depot rejection immediately
If the nominated depot refuses the container, the driver should obtain a gate record, rejection message or other available evidence. Record arrival time, container number, depot, reason given and the person or system issuing the rejection.
Ask the carrier for a revised return instruction in writing. Do not send the driver to another depot based only on an informal suggestion; an unauthorised return may be refused again or create a drop-off charge.
Prepare the Driver Return Pack
Give the driver a concise pack rather than forwarding an entire email chain. It should contain:
- transport order and container number;
- current depot instruction and map reference;
- appointment or pre-advice confirmation;
- delivery order or release copy if required;
- validation or payment confirmation where applicable;
- depot operating hours and contact;
- escalation contact for rejection or delay;
- instruction to obtain the empty-return interchange receipt.
The driver should compare the physical container number with the job order. One incorrect digit can invalidate the instructions.
Close the Return with Evidence
The job is not complete when the truck enters the depot. Collect the empty-container interchange receipt or electronic confirmation and check:
- container number;
- return depot;
- gate-in date and local time;
- recorded equipment condition;
- truck or driver reference;
- receipt or transaction number.
Send the evidence to the party monitoring detention and retain it with the shipment file. If the carrier’s portal does not update, raise the discrepancy before an invoice is issued where possible.
Common Empty-Return Failures
- using a depot from an old delivery order;
- failing to check container-type acceptance;
- missing an appointment or pre-advice step;
- dispatching while carrier validation is pending;
- omitting the free-time status from the transport order;
- accepting depot rejection without written evidence;
- returning to an alternative depot without authorisation;
- failing to collect or check the interchange receipt.
Takeaway
Control the empty return as a shipment milestone. Verify the depot against the specific container, confirm acceptance and free-time status, equip the driver with current instructions and retain gate-in evidence.
For support coordinating container returns and ocean-freight milestones, contact ZSCM Logistics at logis@zscm.ae.
